What Hardware Will You Need for Hanging Your Outdoor Curtains?
Knowing your particular outdoor space and style of outdoor curtains plus how you want your outdoor drapery to function, all will help you in determining the best hardware setup for your own situation. We offer wonderful hardware options for traditional hanging, as well as some suggestions if your outdoor-living space does not offer an immediate means of installing outdoor curtains.

Rods
We carry three sizes of 1.25in diameter curtain rods: 48”, 72”, and 93” long. All sizes are made from steel and powder-coated in a sleek Iron Black finish that is rated for the outdoors—an ideal choice for patios, porches, pergolas, cabanas, and other outdoor (or indoor!) living spaces.
We offer three different end types in our curtain rods: thread connectors on both ends, set screws on both ends, and a thread connector/ set screw mix.
Choose your rod configuration based on your installation:
For standard bracket installations:
-Thread Connectors on Both Ends: Best for one rod per opening, with a finial
attached to each end. The thread connectors are inlayed in the rod for you to simply
screw the finials into each end. Please note that this rod type cannot be connected to
another rod.
-Set Screws on Both Ends: Best for middle rods when connecting multiple rods
together. The set screws (one on each end) are small, inlayed screws that you tighten
down to a Cut Pole Connector with a hex key (provided) to connect multiple rods.
-Thread Connector + Set Screw: Best for end rods when connecting multiple rods.
Attach a finial to the thread connector side and connect another rod to the set screw
side, with the use of a Cut Pole Connector.
For wall-to-wall/ inside-mount installations:
The thread connector is the preferred rod end type for use with a Socket Bracket. Depending on the width of your space, choose Thread Connectors on Both Ends for a single rod or Thread Connector + Set Screw when connecting multiple rods.
Important: A bracket is required at every point where rods connect with a cut pole connector to properly support the connection.
A few installation examples:
- a. 168in/93in = 1.8 round up to 2
- b. I will need to order 2 rods that connect in the middle i. (2) 93in thread connector + set screw mix curtain rods ii. (1) Cut pole connector iii. (3) Standard single steel brackets
A. I am mounting curtain rods to the outside beam of my cabana, and I would like to use finials. The width of my opening is 14ft (168in).
- a. 258in = 93in + 72in + 93in
- b. I will need to order 3 rods- two end rods and one in the middle i. (2) 93in thread connector + set screw mix curtain rods ii. (1) 72in set screws on both ends curtain rod iii. (2) Cut pole connectors iv. (2) Socket brackets v. (2) Simple ceiling steel brackets
- c. I may need to cut the rods down slightly (set screw side) to ensure I leave a little wiggle room for the backplate of each socket bracket.
B. I am mounting curtain rods from one wall to the other (think shower rod installation). The width of my opening is 22ft (258in).
**Please Note: Curtain rods can be cut to length using an electric reciprocating saw, such as a Sawzall. Be sure to cut the correct end of the rod. Do not cut off the thread connector if you plan to install finials, as this will prevent you from attaching them. Whenever possible, avoid cutting off the set screw, which is inlayed about 2 1/4in from the end of the rod. However, if you need to remove the set screw to achieve your desired rod length, you can still use a cut pole connector to join multiple rods. Simply wrap a small piece of electrical tape around the connector to increase its thickness and prevent it from sliding around inside the rods, since the set screws will no longer be available to hold it in place.
Brackets
Inside-Mount / Socket Brackets
Socket brackets are ideal for spaces with built-in boundaries on both sides, such as between columns or walls. Mounted to the inside of these surfaces, they create a clean, streamlined look with minimal visible hardware.
Important: Accurate measurements are essential to ensure the rod fits securely between the socket brackets. Rods may need to be cut to the exact length using an electric reciprocating saw, such as a Sawzall. Unlike traditional wall or ceiling brackets, socket brackets do not require finials.
Finials (for Rod Ends)
Add the perfect finishing touch to your curtain rods with our selection of finials, ranging from simple and understated to decorative statement pieces. Finials screw into the threaded ends of compatible curtain rods, adding style and personality to your outdoor space. Sold in pairs, finials add extra length to your overall rod setup.
Please note: Finials are only compatible with curtain rods featuring the thread connector end option.
Cut Pole Connector
Seamlessly connect multiple curtain rods with our cut pole connector. Designed to fit inside the open ends of our hollow curtain rods, this connector creates a secure connection for longer or custom rod setups.
Please note: This connector is only compatible with rods that have set screws on the ends. A bracket is required at every connection point to properly support the rods.

